NRG Global Instruments

NRG GLOBAL MAKE side-mounted float level switch is suitable for liquid level control of open or bearing pressure container in industrial process. When the liquid level reaches to high or low limit, relay contact point can be as signal alarm device or the switch in electronic pump circuit. It is used in water treatment, petrochemical, furnace, shipyard etc. It is widely applicable in the condition of high viscosity, high pressure, high temperature because of it is flexible structure, and it can replace the UQK series products. Working principle To use of liquid buoyancy principle. When the floating ball due to buoyancy and moving up and down, the magnetic reed switch in the junction box will be action when it is influence by the arm end magnetic. The same principle is used in the micro switch device. To use of magnets and magnet micro switch arm end of mutual exclusion movement to push the micro switch action. Product purpose SM series float level switch is suitable for liquid level control of open or bearing pressure container in industrial process. When the liquid level reaches to high or low limit, relay contact point can be as signal alarm device or the switch in electronic pump circuit.

Minimum order quantity: 10 Piece

NRG MAKE Magnetic Float switch is available with potential Reed Switch contacts in SPST or SPDT. Level Switch with SS, PP, Titanium construction for point level sensing in tanks. For Tank Level Indication. For process automation. For process industries. For Level Measurement.

Minimum order quantity: 1 Piece

NRG GLOBAL INSTRUMENTS MAKE magnetically float operated Top Mounted Level Switch for controlling one or multi Levels by using reed Switch. The Unit Consists of Vertical Guide Pipe (Stem), Reed Switches Are located, Magnetic Float Sliding over the Stem according to the level in the tank.

After passing the float, the reed relay will retain their output state. Various materials of

construction are available depending up on Service Condition. Maximum 4 Set points can be given in a Single Level Switch & Maximum stem length will be 3 Meters.

2. Technical Data

Float                                       : S.S.316 / SS with PTFE / Poly Propylene

Process Connection           : Flanged / Screwed / TC Joint

Flange                                    : Mini 1” NB to Any Size in C.S. / S.S.304 / S.S.316 / SS with PTFE

                                                  Coated / P.P.

Switch                                    : Hermetically Sealed Magnetically Operated Reed Switch with

                                                  Rhodium Contact SPST / SPDT.

Rating                                    : 0.5 Amps @ 24 V DC OR 230 VAC 1 AMP

Switch Housing                   : Die Cast Aluminum, Weather Proof IP 65 (Enclosure) /  

                                                  Flame Proof to II A,  II B (IS – 2148 CMRS Dhanbad Approved)

Operating Pressure            : 10 Kg / Cm2

Operating Temp                 : Max. 90 C.

Cable Entry                          : ½” NPT (F) OR ¾” ET (F)

No of Switches                    : As Per Customer Requirement

Stem Length                        : Up to 3 Meters.. other on your request

Minimum order quantity: 1 Piece

MAKE                                                    : NRG GLOBAL   

HSN CODE                                           : 90261020

TYPE                                                      : VIBRATING FORK

Name of the Fluid                            : SUGAR 

Housing                                                : Pressure Die Cast Aluminium, weatherproof , IP68

Probe Housing Cable Entry           : Threaded, PG 13.5 cable gland, Polyamide

Output                                                  : 1NO, 1NC DPDT Relay Output

                                                                  (rated at 6 A, 230 V AC for non inductive load)

Power Supply                                     : Universal (18 To 55V DC and 90 To 265V at 50Hz AC)

                                                                  on same terminals

Mounting                                            : 1” BSP-M SCREWED END

Vibrating Fork                                    : Fluido Fork, 150 mm,

Probe Length                                     : 150mm

Minimum order quantity: 1 Piece

NRG GLOBAL MAKE Top Mounted Magnetic Level Switch
These are used for controlling one or multi Levels by using reed Switch or micro Switch. It has a magnetized float moving alongside the protection tube (S.S. 316) which tracks the level and activates the reed relays inside the tube.

Minimum order quantity: 1 Piece

NRG GLOBAL MAKE  float rises or falls with liquid levelSENSOR, it moves a magnetic sleeve into or out of the field of a switch actuating magnet, causing switch operation

Minimum order quantity: 1 Piece

We are known as the leading manufacturer, importer, exporter and supplier of a comprehensive assortment of Liquid Level Switches. Used for used for Pump protection & Cooling Circuit protection, made up by utilizing top quality of basic material under the observation of the proficient team of workers, these Flow switches are manufactured at our highly developed

Minimum order quantity: 1 Piece

Conductivity Level Switch is a simple, low cost, point level measurement switch designed for level detection of conductive liquids having low densities, high viscosities, containing solid particles and to detect interface between non-conductive and conductive liquids. The probes work through the variation of the electrical resistance between the reference electrode and the level-control electrode. Conductivity level switches detect the level resistance when their electrodes are covered by the medium. If the tank is made of plastic, concrete, or any other nonconductive material, an additional electrode is required as a reference

• Conductivity Level Switches are available with stainless steel 316 electrodes as standard
• Suitable for many chemicals and aggressive media which are conductive in nature and dirty liquids, liquids with high solid content
• Construction available with both Solid probes & Suspended probes to suit fitting requirement

It is a simple, low cost, point level controller designed for detecton of conductive liquids, having low densites, high viscosities, containing solid particles and interface between nonconductive and conductive liquids.

CONSTRUCTION & OPERATION It comprises of a probe, wired to a level controller. The probe holds one common reference/common electrode and one or multiple “Control Electrodes” depending upon the number of levels to be controlled. All the electrodes are suitably insulated to avoid electrical bridging. The lengths of “Control Electrodes” correspond to the height of preset level points to be controlled and the length of the “reference/common Electrode” is kept slightly longer than the longest “Control Electrode”. If tank is conductive, it can be used as a reference/common electrode. Then number of control electrodes equals number of preset levels. Level controller houses sensing electronics consisting of power supply and signal conditoning circuit which provide a “Low AC Voltage” across mass and control electrodes. On liquid reaching preset level point electrical circuit gets completed - generating a signal which is amplified to actuate a relay, those potential free contacts are available for subsequent operations. On “Level Falling” the circuit breaks, deactivating the relay

Minimum order quantity: 1 Piece

 NRG GLOBAL MAKE side-mounted float level switch is suitable for liquid level control of open or bearing pressure container in industrial process. When the liquid level reaches to high or low limit, relay contact point can be as signal alarm device or the switch in electronic pump circuit. It is used in water treatment, petrochemical, furnace, shipyard etc. It is widely applicable in the condition of high viscosity, high pressure, high temperature because of it is flexible structure, and it can replace the UQK series products.

Working principle

To use of liquid buoyancy principle. When the floating ball due to buoyancy and moving up and down, the magnetic reed switch in the junction box will be action when it is influence by the arm end magnetic. The same principle is used in the micro switch device. To use of magnets and magnet micro switch arm end of mutual exclusion movement to push the micro switch action.

Product purpose

SM series float level switch is suitable for liquid level control of open or bearing pressure container in industrial process. When the liquid level reaches to high or low limit, relay contact point can be as signal alarm device or the switch in electronic pump circuit.

Specification

Application         : Liquids

Liquid Density    : Above 0.5 – 2.0

Liquid Velocity   : Upto 500 cp

Design Pressure               : Upto 40 Kg/cm²

Design Temp      : Upto 300°C

Connection         : Flanged to ASA/BS/DIN Screwed BSP/Screwed NPT

Material               : SS304/SS304L/SS316/SS316L/PP/HDPE/PVC/PVDF Lined/PTFE Lined Other Materials on request

Switch Type        : Micro, SDPT, DPDT

Form                     : 1 NO+1NC / 2NO+2NC

Rating                   : 5 Amp, 230 VAC OR 24 VDC

Enclosure            : W-Proof IP65 / Ex-Proof

Minimum order quantity: 1 Piece

NRG GLOBAL MAKE Displacer type level switches offers the industrial user a wide choice of alarm and control configuration. DLS works on a simple buoyancy principle and is well suited for simple or complex applications, such as forming surging liquids or agitated fluids, and usually costs less than other types of level switches.  

CONSTRUCTION & OPERATION

Operation is based on simple buoyancy principle. As the liquid level rises and progressively immerses the displacer elements, the effective weight suspended on the spring reduces and the consequent length of the spring change is used to provide magnet movement and operate the switch. The spring movement causes the magnetic sleeve to attract a pivoted magnet actuating a switch mechanism located outside the barrier tube. Built-in limit stops, prevent over stroking under level surge conditions.

FEATURES:

• Wide choice of switching functions

• Suitable for large tanks up to 15 meters

• Site adjustable switch points

• Customized for high temp, high pressure & vaccum applications.

• Reliable performance in turbulent liquids even without still pipes.

• Easy transportation of longer length switches.

• Enclosure : Weather proof-IP-65 Ex-proof-Gr. IIA & IIB or IIC

GENERAL SPECIFICATIONS:

Enclosure                    : Cast ALUMINIUM, Weather Proof-IP 65, Cast AL Ex-proof Gr. IIA & IIB or IIC

Conduit Connection    : ¾ ” ET or ½” NPT

Measuring Range       : 200 mm~15000 mm

Operating Differential : 40±5 mm / Adjustable / 65 ±5 mm

Switch Type                 : Micro switch

Switch Contacts           : 2 SPDT (2 NO + 2 NC) @ 5A, 230 VAC (Resistive)

Switch Action              : Bistable

Terminals                    : To suit 1.5 mm2 conductor

Flexible Rope              : SS304, SS316, PP, PTFE

Displacer                     : SS304, SS316, PP, PTFE

Spring Housing            : SS316, PP, PTFE

Spring Material           : SS316, SS316L

Process Connection Flanged : MS, SS304, SS316,  PP (SS clad), PTFE (SS clad)

Perforated still well    : MS, SS304, SS316, PP (65 NB)

External Cage             : MS, SS304, SS316, PP (80 NB)

Max. Temperature     : 0-200°C (without cooling fins)  0-300°C (with cooling fins)

                                     (Contact factory for temperature more than 300°C)

Max. Test Pressure     : Vaccum to 40 Kg/cm2  (Contact factory for pressure more than 40 Kg/cm2)

Min. Sp. Gravity          : 0.7 (Contact factory for Sp. Gr. less than 0.7)

Minimum order quantity: 1 Piece

 NRG GLOBAL MAKE side-mounted float level switch is suitable for liquid level control of open or bearing pressure container in industrial process. When the liquid level reaches to high or low limit, relay contact point can be as signal alarm device or the switch in electronic pump circuit. It is used in water treatment, petrochemical, furnace, shipyard etc. It is widely applicable in the condition of high viscosity, high pressure, high temperature because of it is flexible structure, and it can replace the UQK series products.

Working principle

To use of liquid buoyancy principle. When the floating ball due to buoyancy and moving up and down, the magnetic reed switch in the junction box will be action when it is influence by the arm end magnetic. The same principle is used in the micro switch device. To use of magnets and magnet micro switch arm end of mutual exclusion movement to push the micro switch action.

Product purpose

SM series float level switch is suitable for liquid level control of open or bearing pressure container in industrial process. When the liquid level reaches to high or low limit, relay contact point can be as signal alarm device or the switch in electronic pump circuit.

Specification

Application         : Liquids

Liquid Density    : Above 0.5 – 2.0

Liquid Velocity   : Upto 500 cp

Design Pressure               : Upto 40 Kg/cm²

Design Temp      : Upto 300°C

Connection         : Flanged to ASA/BS/DIN Screwed BSP/Screwed NPT

Material               : SS304/SS304L/SS316/SS316L/PP/HDPE/PVC/PVDF Lined/PTFE Lined Other Materials on request

Switch Type        : Micro, SDPT, DPDT

Form                     : 1 NO+1NC / 2NO+2NC

Rating                   : 5 Amp, 230 VAC OR 24 VDC

Enclosure            : W-Proof IP65 / Ex-Proof

Minimum order quantity: 1 Piece

 NRG GLOBAL MAKE side-mounted float level switch is suitable for liquid level control of open or bearing pressure container in industrial process. When the liquid level reaches to high or low limit, relay contact point can be as signal alarm device or the switch in electronic pump circuit. It is used in water treatment, petrochemical, furnace, shipyard etc. It is widely applicable in the condition of high viscosity, high pressure, high temperature because of it is flexible structure, and it can replace the UQK series products.

Working principle

To use of liquid buoyancy principle. When the floating ball due to buoyancy and moving up and down, the magnetic reed switch in the junction box will be action when it is influence by the arm end magnetic. The same principle is used in the micro switch device. To use of magnets and magnet micro switch arm end of mutual exclusion movement to push the micro switch action.

Product purpose

SM series float level switch is suitable for liquid level control of open or bearing pressure container in industrial process. When the liquid level reaches to high or low limit, relay contact point can be as signal alarm device or the switch in electronic pump circuit.

Specification

Application         : Liquids

Liquid Density    : Above 0.5 – 2.0

Liquid Velocity   : Upto 500 cp

Design Pressure               : Upto 40 Kg/cm²

Design Temp      : Upto 300°C

Connection         : Flanged to ASA/BS/DIN Screwed BSP/Screwed NPT

Material               : SS304/SS304L/SS316/SS316L/PP/HDPE/PVC/PVDF Lined/PTFE Lined Other Materials on request

Switch Type        : Micro, SDPT, DPDT

Form                     : 1 NO+1NC / 2NO+2NC

Rating                   : 5 Amp, 230 VAC OR 24 VDC

Enclosure            : W-Proof IP65 / Ex-Proof

Minimum order quantity: 1 Piece

1. Product Description

NRG GLOBAL  Introduced magnetically float operated Top Mounted Level Switch for controlling one

or multi Levels by using reed Switch. The Unit Consists of Vertical Guide Pipe (Stem), Reed

Switches Are located, Magnetic Float Sliding over the Stem according to the level in the tank.

After passing the float, the reed relay will retain their output state. Various materials of

construction are available depending up on Service Condition. Maximum 4 Set points can be

given in a Single Level Switch & Maximum stem length will be 3 Meters.

2. Technical Data

Float : S.S.316 / SS with PTFE / Poly Propylene

Process Connection : Flanged / Screwed / TC Joint

Flange : Mini 1” NB to Any Size in C.S. / S.S.304 / S.S.316 / SS with PTFE Coated / P.P.

Switch : Hermetically Sealed Magnetically Operated Reed Switch with Rhodium

 Contact SPST / SPDT.

Rating : 0.5 Amps @ 24 V DC

Switch Housing : Die Cast Aluminum, Weather Proof IP 65 (Enclosure) /

 Flame Proof to II A, II B (IS – 2148 CMRS Dhanbad Approved)

Operating Pressure : 10 Kg / Cm2

Operating Temp : Max. 90 C.

Cable Entry : ½” NPT (F) OR ¾” ET (F)

No of Switches : As Per Customer Requirement

Stem Length : Up to 3 Meters

3. Design features

1. One Moving Component Exists, so that no – wear of float.

2. Suitable for any fluid having Specific Gravity Above 0.7

3. Minimum possible Distance between 2 Level set Points is 75 mm.

4. Accuracy : ± 0.10%, ± 0.25 %, ± 0.5 % on F.S.

5. The switch operates on the principle of magnetic flux coupling with no mechanical

 connection so that fluid contamination of switch components cannot occur.

4. Ordering Information

Information Required to Quote: Material of Construction, Service Medium, Specific Gravity,

Max. Pressure & Temperature, Number of Actuating Levels & Their Distance from top of the

Connection, Process Connection.

Minimum order quantity: 1 Piece

1. Product Description

NRG GLOBAL  Introduced magnetically float operated Top Mounted Level Switch for controlling one

or multi Levels by using reed Switch. The Unit Consists of Vertical Guide Pipe (Stem), Reed

Switches Are located, Magnetic Float Sliding over the Stem according to the level in the tank.

After passing the float, the reed relay will retain their output state. Various materials of

construction are available depending up on Service Condition. Maximum 4 Set points can be

given in a Single Level Switch & Maximum stem length will be 3 Meters.

2. Technical Data

Float : S.S.316 / SS with PTFE / Poly Propylene

Process Connection : Flanged / Screwed / TC Joint

Flange : Mini 1” NB to Any Size in C.S. / S.S.304 / S.S.316 / SS with PTFE Coated / P.P.

Switch : Hermetically Sealed Magnetically Operated Reed Switch with Rhodium

 Contact SPST / SPDT.

Rating : 0.5 Amps @ 24 V DC

Switch Housing : Die Cast Aluminum, Weather Proof IP 65 (Enclosure) /

 Flame Proof to II A, II B (IS – 2148 CMRS Dhanbad Approved)

Operating Pressure : 10 Kg / Cm2

Operating Temp : Max. 90 C.

Cable Entry : ½” NPT (F) OR ¾” ET (F)

No of Switches : As Per Customer Requirement

Stem Length : Up to 3 Meters

3. Design features

1. One Moving Component Exists, so that no – wear of float.

2. Suitable for any fluid having Specific Gravity Above 0.7

3. Minimum possible Distance between 2 Level set Points is 75 mm.

4. Accuracy : ± 0.10%, ± 0.25 %, ± 0.5 % on F.S.

5. The switch operates on the principle of magnetic flux coupling with no mechanical

 connection so that fluid contamination of switch components cannot occur.

4. Ordering Information

Information Required to Quote: Material of Construction, Service Medium, Specific Gravity,

Max. Pressure & Temperature, Number of Actuating Levels & Their Distance from top of the

Connection, Process Connection.

Minimum order quantity: 1 Piece

1. Product Description

NRG GLOBAL  Introduced magnetically float operated Top Mounted Level Switch for controlling one

or multi Levels by using reed Switch. The Unit Consists of Vertical Guide Pipe (Stem), Reed

Switches Are located, Magnetic Float Sliding over the Stem according to the level in the tank.

After passing the float, the reed relay will retain their output state. Various materials of

construction are available depending up on Service Condition. Maximum 4 Set points can be

given in a Single Level Switch & Maximum stem length will be 3 Meters.

2. Technical Data

Float : S.S.316 / SS with PTFE / Poly Propylene

Process Connection : Flanged / Screwed / TC Joint

Flange : Mini 1” NB to Any Size in C.S. / S.S.304 / S.S.316 / SS with PTFE Coated / P.P.

Switch : Hermetically Sealed Magnetically Operated Reed Switch with Rhodium

 Contact SPST / SPDT.

Rating : 0.5 Amps @ 24 V DC

Switch Housing : Die Cast Aluminum, Weather Proof IP 65 (Enclosure) /

 Flame Proof to II A, II B (IS – 2148 CMRS Dhanbad Approved)

Operating Pressure : 10 Kg / Cm2

Operating Temp : Max. 90 C.

Cable Entry : ½” NPT (F) OR ¾” ET (F)

No of Switches : As Per Customer Requirement

Stem Length : Up to 3 Meters

3. Design features

1. One Moving Component Exists, so that no – wear of float.

2. Suitable for any fluid having Specific Gravity Above 0.7

3. Minimum possible Distance between 2 Level set Points is 75 mm.

4. Accuracy : ± 0.10%, ± 0.25 %, ± 0.5 % on F.S.

5. The switch operates on the principle of magnetic flux coupling with no mechanical

 connection so that fluid contamination of switch components cannot occur.

4. Ordering Information

Information Required to Quote: Material of Construction, Service Medium, Specific Gravity,

Max. Pressure & Temperature, Number of Actuating Levels & Their Distance from top of the

Connection, Process Connection.

Minimum order quantity: 10 Piece

NRG GLOBAL MAKE Designed for single point tank monitoring, compact liquid-level switches operate based on non-contact magnetic float and reed switch technology. This design allows for high accuracy fluid level detection of various liquids, including acids and chemicals. The compact style makes mini float switches perfect for tight spaces and small tanks, levels, and containers.

elobau’s miniature float type level switches are available in different materials for compatibility with a wide range of fluids, temperatures, and pressures. A robust design and durable housing give our float level switch a long operating life, even in demanding operating conditions.

Minimum order quantity: 1 Piece

Float level sensors are continuous level sensors featuring a magnetic float that rises and falls as liquid levels change. The movement of the float creates a magnetic field that actuates a hermetically sealed reed switch located in the stem of the level sensor, triggering the switch to open or close.
 
Different variations of float switches are used for commercial and industrial applications involving water, oil, chemicals, and other liquid materials. There are vertical mount and side mount options, and the choice of a stem made from either hard plastic or non-magnetic metal such as stainless steel.
 
We manufacture several varieties of float switches including programmable level sensors, miniature float switches, suction pipe sensors, and bulk material switches. All our products feature a robust housing design and are offered in various configurations to meet your unique needs.  Learn more about our float level sensor products below or contact us for assistance in selecting the right option for your application and operating environment.

Minimum order quantity: 1 Piece

Float level sensors are continuous level sensors featuring a magnetic float that rises and falls as liquid levels change. The movement of the float creates a magnetic field that actuates a hermetically sealed reed switch located in the stem of the level sensor, triggering the switch to open or close.

Minimum order quantity: 1 Piece

NRG MAKE vibrating fork is a level switch for liquids and is used in tanks, containers and pipelines.As a sturdy replacement of conventional float switch, Elixir offers a variety of built-in featuresnon-existant in floats and other switches, e.g. where materials are sticky, corrosive, agitated,splashing, foaming and having uncertain electrical properties.Elixir vibrating fork is suitablefor hazardous areas, available with explosion-proof housings certified by CMRI , Dhanbad.Features• Less Power Consumption: Less Heat, Long Life• Universal Power Supply: 18 to 55 V DC,90 to 265 V AC on same terminals• Application Temperature Range : up to 200° C• Suitable up to 10,000 cP (Detects all Industrial Fluids)• Compact Size: Less Inventory• Extendable probe length from 68 to 3000 mm• ECTFE coated, polished & hygienic fork• Output: 8.2V Namur, SPDT & DPDT Relay type currentoutput• Calibration Free, independent of material's dielectricpropertiesPrincipleA specially shaped tuning fork is kept vibrating using piezo-electric elements. Typically, thefork vibrates at its natural frequency. The frequency of oscillation for the tuning fork changeswhen immersed in liquids. The change in frequency is detected by the microprocessorleading to a switching decision.Manufacturing Level Instruments & Speed Monitoring SystemsVersion 2.1Grown...to meet challengesELIXIR Microcontrollerbased Vibrating Fork Liquid Level Limit SwitchApprovals CE Marking, RoHS Compliance, IP-67 Marking

Minimum order quantity: 1 Piece

Point level detection with Rotary paddle switch

Depending on the requirements the rotary paddle level sensors are used as a full, demand or empty detector in storage silos or process vessels and is suitable for use in almost all solids. With their simple electromechanical measuring principle, they can also be adapted to extreme process conditions. The UWT rotary paddle level switches can be used in applications with process temperatures of up to 1100°C and process pressures of up to 10 bar.

The robust and versatile functional principle is based on a motor-driven, rotating measuring blade, which is inhibited in its rotary motion when covered with bulk material. This creates a counter-torque which is converted into the electrical output signal "covered" via a swivel movement at a switch. If the bulk material no longer covers the measuring blade, the switch is reset to its initial position via a spring. The original state is reached again, the output signal is inverted.

Established in the year 2020, NRG GLOBAL is an accomplished manufacturer, trader and exporter of a wide range of measuring instrument. Our aim from day one has been to offer world-class products to customers at very reasonable prices. This has driven us to follow the latest technical advancements in the industry and enhance our product range by incorporating the same into our offerings.The company was founded and has grown under the great leadership of our owner Mr. RIKESH BHAGAT who has along with our top-management team has dedicated himself to the growth and well-being of the organization. With comprehensive domain expertise and experience, he provides us with valuable direction and guidance that has helped us in being a leader in this industry.We believe in achieving overall excellence in all our functions.

Minimum order quantity: 1 Piece

Nrg global vibrating fork is a level switch for liquids and is used in tanks, containers and pipelines.As a sturdy replacement of conventional float switch, Elixir offers a variety of built-in featuresnon-existant in floats and other switches, e.g. where materials are sticky, corrosive, agitated,splashing, foaming and having uncertain electrical properties.Elixir vibrating fork is suitablefor hazardous areas, available with explosion-proof housings certified by CMRI , Dhanbad.Features• Less Power Consumption: Less Heat, Long Life• Universal Power Supply: 18 to 55 V DC,90 to 265 V AC on same terminals• Application Temperature Range : up to 200° C• Suitable up to 10,000 cP (Detects all Industrial Fluids)• Compact Size: Less Inventory• Extendable probe length from 68 to 3000 mm• ECTFE coated, polished & hygienic fork• Output: 8.2V Namur, SPDT & DPDT Relay type currentoutput• Calibration Free, independent of material's dielectricpropertiesPrincipleA specially shaped tuning fork is kept vibrating using piezo-electric elements. Typically, thefork vibrates at its natural frequency. The frequency of oscillation for the tuning fork changeswhen immersed in liquids. The change in frequency is detected by the microprocessorleading to a switching decision.Manufacturing Level Instruments & Speed Monitoring SystemsVersion 2.1Grown...to meet challengesELIXIR Microcontrollerbased Vibrating Fork Liquid Level Limit SwitchApprovals CE Marking, RoHS Compliance, IP-67 Marking

Minimum order quantity: 1 Piece

MAKE                              : NRG GLOBAL

TYPE                                : DISPLACER FLOAT TYPE

NAME OF THE FLUID           : LIQUID

Temperature                    : 200 deg C

Pressure                           : 10 kg/cm2 g

Sp Gr / Density                            : 0.7 – 2.0

Viscosity                           : 0.5 - 20 Cp

WETTED PARTS (MOC)         : SS304

DISPLACER FLOAT               : 2 NOS  SS304 OF 38 MM DIA

SPRING                            : S.S.304

STEM                               : SS304

FLOAT WIRE                      : SS304  HAVING 1 MM DIA

SIZE                                 : 4” ASA 150 # RF 

CONNECTION MOC             : SS304 FLANGE 

ENCLOSURE / HOUSING       : ALUMINIUM DIE CAST FLAME PROOF  

SWITCH                           : IMPORTED micro SWITCH

SWITCH CONTACT               : 2NC + 2NO+ COM POTENTIAL FREE CONATCT 

                                          230 VAC  5 AMP

CABLE ENTRY                    : ½” -F 

ACCESSORIES                    : NA

STEM LENGTH                    : 1.7 MTRS.

HIGH LEVEL FROM TOP        : 0.5 MTR - ADJUSTABLE

LOW LEVEL FROM TOP        : 1.7 MTR – ADJUSTABLE

NRG GLOBAL make level switch

Minimum order quantity: 1 Piece

Point level detection with Vibration Level Limit Switches

Depending on the requirements, vibrating level limit switches are used as full, demand or empty detectors in storage silos or process vessels and are suitable for use in almost all media. The main component of the vibrating level limit switch is a piezo stack which is electrically excited and thereby vibrates. The design of this piezo stack largely defines the range of application. UWT vibrating level limit switches are suitable for process temperatures up to 150°C and process pressures up to 16 bar.

Vibrating level limit switches are differed between vibration fork and vibrating rod, which differ in their mechanical design but not in their operating principle.

Minimum order quantity: 1 Piece

NRG capacitance level limit switch offers a solution for level limit detection offine, coarse, bulky solids, nonstickyslurries and liquids. The measuring systemconsists of an evaluation unit, an electronic insert and a probe. It works by utilizingthe dielectric property of the application material.PrincipleThe probe comprises of a sense electrode, electrically isolated from the metallic tank bymeans of a suitable insulator. The sense electrode and the vessel wall serve as the twoelectrodes of a capacitor with the service material acting as the dielectric. A change in thelevel of material causes a change in the dielectric, which in turn causes the value of this tankcapacitor to change.Approvals CE Marking, Flameproof Enclosure (Gas Groups IIA, IIB, IIC), RoHS Compliance